Your Step-by-Step Guide to How to Reupholster a Chair (2024)

• Total Time:1 day
• Skill Level:Intermediate
• Estimated Cost:$50 to $200
• Yield:One reupholstered chair

How to Reupholster a Chair

1. 

   Remove Old Fabric

   Disassemble the chair as needed and remove the upholstery pieces, taking care not to tear any of the old pieces of fabric—you will need them as patterns.

   Begin by removing the black cloth from the underside of the chair, then loosen the pieces attached to the frame. Remove the pieces and mark each with its location on the chair with a marking pen. For example, label the pieces as outside back, right side back, left side back, inside back, seat, and seat sides. Mark "T" for the top or "F" for the front to indicate the direction of the piece on the chair.

   Note on each piece the location of welting and where pieces are sewn together. Save pieces of welting and tack strips to use as a measure for new pieces.

   Photograph the chair before you strip the original covering, taking full-length and detailed photos for reference.

   Crucial Tips You Need to Know Before Reupholstering Furniture

2. 

   Replace Batting

   If worn or stained, remove old batting from chair back and seat. Check springs and webbing for damage and repair if necessary. Sand, prime, and paint the frame or legs if desired; let dry.

   Cut a piece of 1/2-inch-thick batting to cover the chair back and seat, if needed. Cover the chair back first, stapling it down. Pull gently on the batting around each staple to prevent visible indents from the staples so the staple is inside the batting. Next, cover the seat with batting in the same way, folding neatly around the corners.

3. 

   Make New Pattern

   Lay the original upholstery pieces wrong-side up on the wrong side of the new fabric, watching for the grain, placement, and direction of the pattern or motifs. Pin in place and cut around the pattern, leaving 2 to 3 inches of fabric beyond the stapled edges of the original pieces. This will give you fabric to grasp when stapling; the original pieces were trimmed after they were stapled. Repeat this process to cut out each fabric section. Transfer the markings for direction, welting, and seams onto the new pieces with chalk.

   If preferred, combine the chair reupholstery pieces into covers for the seat and back that can be applied all at once. Place the fabric sections together inside out and sew together, adjusting for curves as needed.

   The 8 Best Sewing Machines of 2024, According to Testing

   See Also

   Beginner's Guide To Reupholstering Furniture

4. 

   Attach Base Fabric

   Place the new inside back, right-side back, and left-side back pieces on the chair in the appropriate locations, using the "T" markings and your photos as guides. Pin the pieces together, making any necessary adjustments to the fit; you may need to trim excess fabric to make it fit snugly. When you're pleased with the fit, pull fabric taut and staple in place on the apron of the chair seat. Use as many staples as necessary to secure the fabric and keep it smooth. Be sure you place staples on the back of the chair where the back panel will cover them. Trim excess fabric.

   If using a cover, apply the new cover to the seat base and adjust as needed. Pull the fabric taut and staple to the frame where the old cover was previously attached, starting at the front edge and working toward the back. Tuck excess fabric under at the corners.

5. 

   Make Welting

   Using the old pieces as your guide, determine the length of the welting needed to go around the seat apron at the top and bottom. Cut enough 2-inch-wide bias strips to equal that length, allowing a few extra inches. Join the strips with diagonal seams and trim the seam allowance to 1/2 inch. Fold the bias strip around the cord and use a zipper foot to sew in place. The welting will go around the bottom of the seat apron.

   How to Make Welting for Your DIY Upholstery Project

6. 

   Sew Welting

   Pin the side panel to the seat fabric, making any necessary adjustments to the fit or pattern placement. Mark the position for the bottom welting. Remove the side fabric from the chair and sew the welting to the right side of the panel, at the top and where marked near the bottom, starting and ending at the back. For a finished edge, fold the end of the piping under before attaching.

7. 

   Attach Sides

   Holding the right side of the panel up against the seat, staple the top welting in place around the seat. Add a tack strip around the panel top against the welting and staple in place. Fold the side panel down over the tack strip, pull tight, and staple in place to the underside of the chair, with the bottom welting fitting snugly along the edge. Snip notches in the fabric underneath the seat as you smooth around corners. Tuck any excess fabric underneath using a flathead screwdriver.

   The 8 Best Electric Screwdrivers of 2024

8. 

   Attach Back

   Place back panel in position and fold the right side over the top of the chair back. Apply a tack strip to the top of the back rear and staple in place. Fold the panel back over the strip and pull tight toward the bottom of the chair back. Fold bottom edge under and staple to the underside of the chair back.

   If using a cover for the back, slip it over the chair back. Pull the fabric tight and staple to the frame where previously attached. Tuck under raw edges where visible.

   Reassemble the chair if needed. Trim any excess string or fabric.
   

   Use fabric glue or decorative upholstery tacks to secure excess fabric to the back of the reupholstered chair.
   

9. 

   Attach Underside to Finish Chair Reupholstery

   Cut a piece of black breathable fabric for the underside of the chair using the old piece as your guide. Flip the chair upside down, and staple fabric to the underside to conceal any springs or webbing and act as a dust cover. Make sure the fabric is tight against the welting and that it covers up all raw edges of the upholstery fabric. Turn right-side up, and enjoy your newly reupholstered chair.

More DIY Decor Projects

Now that you know how to reupholster a chair, try your hand at other decor updates. You can repaint furniture for a colorful refresh or wallpaper the back of a cabinet or bookshelf with a bold pattern. Stencil a tile floor that looks worn for an inexpensive update, or use stencils to add design to walls without investing in wallpaper. Speaking of wallpaper, peel-and-stick is a great way to experiment with wall coverings without committing to it long-term—just remove it if you grow tired of it. You can update backsplash tiles with peel-and-stick products, too. DIY decor is a creative and budget-friendly way to infuse your home with your personality.